![]() CATEGORIES: BiologyChemistryConstructionCultureEcologyEconomyElectronicsFinanceGeographyHistoryInformaticsLawMathematicsMechanicsMedicineOtherPedagogyPhilosophyPhysicsPolicyPsychologySociologySportTourism |
Andrew Davidhazy Rochester Institute of Technology School of Photographic Arts and Sciences Imaging and Photographic Technology Department Lomb Memorial Drive, Rochester NY, 14623Special Effects Photography (this material was prepared for the Focal Encyclopedia of Photography) This term includes a whole host of techniques that photographers use to create images that may or may not resemble reality but which usually have some unreal or questionable quality about them. Usually the purpose behind using special effects is to raise the impact or level of interest of an image or to produce images that only exist due to the use of such effects. Special effects depend on the basic belief that photographs don't lie. They exploit this premise by presenting to the observer images that are seemingly impossible to achieve in reality or which enhance certain features of a subject beyond that achievable by normal photographic methods. In addition, special effects often enhance or modify reality for some ulterior purpose such as to enhance aesthetic merit, to convey information in a more effective manner than would be possible with a standard photograph, or to confuse or deceive the viewer into a false interpretation of reality. Special effects and Trick Photography are sometimes considered synonymous but the word trick suggests that the photographs are intended to entertain viewers rather than serve more serious artistic and professional purposes. A precise definition of what comes under the heading of special effects is difficult to give because some manifestation of a special effect can be found in most photographs. Although one can safely assume that "special effects" are not involved when the resulting photograph closely resembles the scene being photographed, when it is as accurate a record of the original scene as a two dimensional representation of a three dimensional scene allows, if it is an instantaneous and sharp record, if it was not manipulated after the image was recorded, and if it appears to be natural and unmanipulated, even in this case certain special effects could have been used by the photographer to achieve this look of naturalness and spontaneity. Also, a special effect that is used so frequently that it becomes commonplace tends to no longer be considered a special effect. The advent of electronic image storage, manipulation and output has had a significant impact on the degree of sophistication and scope of special effects. Not only has this technology allowed for improved quality in creating traditional effects but it has made possible the creation of images that were totally impossible in the past. In spite of this, however, because computer generated special effects require expensive computer equipment and computer skills, their use by photographers is limited. Only special effects produced by standard methods by still photographers will be considered here. Special effects can be classified according to a variety of criteria. Some occur prior to the making of the photograph. Others are used during photography and yet a third class of special effect is that which is accomplished by modifying the original image after the initial photograph is recorded. They could also be classified based on the procedures used or the technology involved. The techniques can be optical, chemical, physical, photographic, electronic, or combinations of these methods. In fact, there are so many techniques that could be called "special" that it becomes impossible to attempt to list, classify, and discuss all of them. Instead, under generalized headings below are listed and described some of the more popular current techniques that are connected with this subject heading.
TEMPORAL EFFECTS Based on the widely held conception that photographs are instantaneous records of a scene photographers exploit this by purposely exposing a scene piecemeal onto a piece of photosensitive material. These sequentially-made images are then viewed by an audience instantaneously. Because of this discrepancy between the production step and the perceptual experience the audience tends to be amazed and/or confused when viewing the final product. Several techniques exploit this concept.
Matte boxes in photography- The idea is that if a dark, featureless obstruction is placed in front of a camera, the film will receive no exposure where this obstruction is located. If without moving the film another exposure is then made of a similar obstruction but one such that it is the exact opposite of the first one in terms of areas that it covers, then the second exposure will seamlessly blend into the areas that were unexposed by the first exposure. These obstructions are called masks. One mask is called a positive mask, the other a negative mask. The simplest example of how one might use such a set of masks is the making of a photograph where one individual appears in two or more locations in the same scene. Problems that photographers need to consider include the fact that there must be no movement across the delimiting boundaries of the "masks", the camera must remain locked in position and the film must remain stationary between the two exposures. Self cocking shutters are preferred although many current cameras are fitted with means to recock the shutter while introducing no film motion into the system. The matte box also allows photographers to combine two or more scenes together on one piece of film by using two masks that are complements of each other placed sequentially in front of the camera. The outline of the mask edge sometimes becomes visible when this process is practiced but when used successfully this is made to actually contribute to the final product's visual appeal.
Matte-boxes in printing-
Focal plane shutter distortion- This effect, produced by a combination of relatively slow moving focal plane shutter and panning the camera to keep up with the moving vehicle (but not quite fast enough) is one that is normally not seen in everyday use of modern cameras also equipped with focal plane shutters. The reason for this is that in these cameras the shutter slit moves much faster than in the older models. Note that exposure time is not a factor in producing the effect, just shutter slit velocity. Slit-scan cameras- Several schemes have been developed for this. One is to devise a means for slowly releasing or winding the shutter of cameras equipped with large focal plane shutters, such as the Speed Graphic or the Graflex or to build an oversized matte-box on the front of which one installs a mechanism for slowly moving an open slit in front of the camera lens while the camera shutter is left locked in the open position. With either system it is fairly difficult to predict what the final photograph will look like because one usually loses the ability to view through the lens once the shutter is open. To deal with this problem one may use some kind of a movable guiding finder that has been coupled to the location of the moving slit. It is also possible to use a camera that is equipped with a pellicle mirror based viewing system located behind the camera lens. Early examples of the application of this technique were photographs made by Robert Doisneau of couples dancing and appearing to be intertwined about each other. Scanning wide angle cameras- Distortion normally not seen in cameras equipped with standard focal plane shutters becomes a matter of concern with these scanning wide angle type cameras because they turn the scanning lens over a relatively significant period of time. This introduces the possibility that a subject may move during the scanning action of the camera, or the camera itself may be significantly changed in position, leading to an alteration of the expected shape of a subject. Several photographers have modified these cameras by slowing down the scanning action in order to produce highly unusual visual effects. John Zimmermann used such a modified camera to portray basketball, baseball and tennis players in amusing and unusual contortions.
Strip Cameras: linear, panoramic and peripheral- Strip cameras are basically classified as linear or photofinish, panoramic, and peripheral designs. These cameras are essentially derivatives of focal plane shutters in that images are exposed sequentially. In strip cameras, however, the moving focal plane shutter is replaced with a stationary slit of (sometimes) variable width past which the film is moved at a fixed or variable velocity. When an image of a subject moves past the slit at a velocity that matches that of the film a sharp record of the subject is impressed onto the film because relative to each other the film and the moving image are stationary. Mismatch between the image velocity and film velocity will cause records of subjects to appear compressed if the film is traveling slower than the image or elongated and stretched out if the film is traveling past the slit more quickly than the image. Probably the most widespread application of strip cameras is in the photography of the order of arrival at the finish line of participants in a racing event. Unusual distortions of arms, legs and torsos are typically inevitable because the film can only match one image velocity while the subjects are moving at a great number of velocities simultaneously. Two photographers who have explored the application of photofinish-type cameras for effective sports photography are George Silk and Neil Leifer, both associated with Time/Life. Operating principles associated with strip camera technology are also the basis for the Cirkut panoramic camera design as well as that of the various modern versions of these cameras that were introduced on a rather large scale commercial basis by the Eastman Kodak Company in the early 1900's.
Panoramic strip cameras rotate about a point roughly under the lens' rear nodal point as they scan the surrounding scene. They must remain level otherwise the horizon line appears to curve sinusoidally. These cameras can easily cover a horizontal angle of view of up to 360 degrees. They reproduce still subjects quite well but moving subjects are distorted in shape.
Opposed to panoramic cameras, peripheral cameras consist of the same basic camera design but they hold the camera stationary while rotating the subject in front of the camera. The slit of the camera is aimed at the center of rotation of the subject. When the subject has made one 360 degree turn, the moving film, made to move at the approximate velocity of the moving image of the subject, will have accumulated information about the whole surface, or periphery, of the subject. A cylindrical subject can be reproduced without distortion but a subject containing 3 dimensional surface features that do not fit within a cylindrical shape will unavoidably be distorted. Features that are farther from the axis of rotation than those for which the camera is adjusted will appear compressed and those that are closer to the center of rotation, and thus have a lower linear velocity, will appear expanded or stretched out. A special version of the standard strip camera is one in which the film is made to move in circular, rather than linear, motion behind the slit to compensate for variations in image velocity along the slit of the camera. This design can produce a peripheral image that correctly reproduces the surface features of a conical subject or a panoramic record that is a conical projection of the scene which surrounded the camera during photography. In this latter case the panoramic camera is tilted while rotating about a vertical axis.
OPTICAL EFFECTS The use of various optical accessory devices allows the making of multiple images by the use of mirrors or prismatic filters typically placed in front of the camera lens. Other optical and photographic techniques also allow for the combination of foreground and background subject matter. Mirrors and Kaleidoscopes- The use of plane mirrors as special effect tools is probably best exemplified by their use in kaleidoscopes. In this case the camera photographs the multiple images of a subject as reflected in the kaleidoscope. Kaleidoscopes and mirrors can be used in various locations in an optical system or during the making of a photograph. Usually they are used in front of a camera lens but they can also be used within an enlarger located between the film and the enlarging lens. It is also possible to use them on a copy stand or duplicating device and placed either between the lens and the subject or between the lens and the film. An SLR camera with built-in meter is a must for these applications. Another possibility is to use a horizontal mirror in front of camera lens covering lower part of a scene to obtain a lake or mirage-type reflection. Partially reflecting mirrors can be used to produce ghost-like images by the simultaneous exposure of a subject located in front of the camera with another subject located off-axis whose image is reflected into the camera lens by way of a semi-transparent mirror. Typically the scheme works best if the off-axis subject is placed against a black background so that unwanted detail surrounding the "apparition" is not visible in the scene. Front Projection- The subject is placed in front of the screen and illuminated with tungsten or electronic flash in such a manner as to be consistent in direction, quality and quantity with the illumination present in the background scene. Typically the light falling on the subject is directed away from the surface of the screen although some spill is allowed. Although the projected image of the background falls on the subject as well as the screen, it does not show up on the subject because the directionality and reflectivity of the screen is many times greater than that of the subject. The final effect is that the subject appears placed in front of the background projected on the screen.
In Camera-Masking- The technique consists of a sequential exposure process. The camera is usually equipped with some means to place a transparency of the desired locale in contact, or almost so, with the film on which the record will be made. This limits the technique to use with large format view cameras. The subject is placed against a black background and lit so that no light falls on the background and so that it is consistent with the lighting of the background scene. During this exposure the areas where the background will later appear have therefore not been exposed. After this first exposure, the background is changed to white and the film, with the background scene now placed in contact with the camera film is exposed again. Since the subject now appears in silhouette, black against a white background, during this second exposure only those parts of the contacted image will print onto the film through which light from the white background passes. Upon development the subject will appear "imprinted" onto the selected background. Care must be taken to ensure that the film and subject remain absolutely stationary during the process and that light does not spill on the background during the subject exposure or on the subject during the background exposure. Front projection and in-camera masking have largely replaced the paste-up method of combining images from two or more photographs. Zooming while shooting or during copying-
Date: 2016-01-03; view: 888
|