1 Underground salt deposits are usually discovered by prospectors searching for water or oil. When salt is detected, a diamond-tipped, hollow drill is used to take several regularly spaced core samples throughout the area. These samples are analyzed to determine if salt mining would be profitable.
2 When a site is selected for mining, shafts are sunk into the center of the salt deposit. Then a machine that looks like a gigantic chain saw is used to cut a slot about 6.0 inches (15 cm) high, about 66 feet (20 m) wide, and about 10 feet (3 m) deep into the salt at floor level. This process is known as undercutting. A series of holes are drilled into the undercut salt with an electric drill containing a tungsten carbide bit. These holes are filled with an explosive such as dynamiteor ammonium nitrate. Electric blasting caps connected to long wires are attached, and the explosive is detonated from a safe distance. Cutting and blasting are repeated in a pattern that leaves pillars of salt standing to support the roof of the mining area. This is known as the room-and-pillar method and is also used in coal mines.
3 Chunks of blasted rock salt are transported to an underground crushing area. Here they are passed over a grating known as a grizzly which collects pieces smaller than about 9 inches (23 cm). Larger pieces are crushed in a rotating cylinder between metal jaws with spiked teeth. The salt is then transported outside the mine to a secondary crushing area where a smaller grizzly and a smaller crusher reduce the particle size to about 3.2 inches (8 cm). At this point foreign matter is removed from the salt, a process known as picking. Metal is removed by magnetsand other material by hand. Rocky material may also be removed in a Bradford breaker, a rotating metal drum with small holes in the bottom. Salt is dumped into the drum, breaks when it hits the bottom, and passes through the holes. Rocky matter is generally harder than salt, so it does not break and does not go through. The picked salt then goes to a tertiary crushing area, where an even smaller grizzly and crusher produce particles about 1.0 inch (2.5 cm) in size. If smaller particles are needed, the salt is passed through a grinder consisting of two metal cylinders rolling against each other. If purer salt is needed, rock salt is dissolved in water to form brine for further processing. Otherwise the crushed or ground salt is passed through screens to sort it by size, poured into bags, and shipped to the consumer.
Processing brine
4 The simplest method of evaporating brine is solar evaporation, but it can only
Rock salt is simply crystallized salt. It is the result of the evaporation of ancient oceans millions of years ago. Large deposits of rock salt are found in the United States, Canada, Germany, eastern Europe, and China.
be used in hot, dry, sunny places. The brine is collected into shallow ponds and allowed to evaporate in the sun. Insoluble impurities such as sand and clay and slightly soluble impurities such as calcium carbonate settle to the bottom as evaporation begins. The brine is pumped or moved by gravity flow to another pond where calcium sulfate settles out as evaporation continues. The remaining brine is moved to yet another pond where the salt settles out as evaporation proceeds. The brine is moved one more time before evaporation is complete to prevent highly soluble impurities such as magnesium chloride, magnesium sulfate, potassium chloride, and magnesium bromide from settling out with the salt. These substances may be collected separately for commercial use.
5 The salt is scooped up by machines running on temporary railroad tracks laid on top of the layer of salt. It is then washed with highly concentrated salt water. This water contains so much salt that it cannot hold any more, so the salt is washed free of any trace impurities without dissolving. The washed salt is removed from the salt water, rinsed with a small amount of fresh water, and piled into huge stacks to drain for two or three months. At this point the salt is about 99.4% pure and can be used for many industrial purposes. If purer salt is needed, it is rewashed in salt water and fresh water, allowed to drain for one or two days, then dried in a hot air oven at about 365°F (185°C). This salt is about 99.8% pure and can be used for food processing.
6 Most brine is processed by a multiple-effect vacuum evaporator. This device consists of three or more closed metal cylinders with conical bottoms. Brine is first treated chemically to remove calcium and magnesium compounds. It then fills the bottom
Brine is water containing a high concentration of salt. The most obvious source of brine is the ocean, but it can also be obtained from salty lakes and underground pools of salt water.
of the cylinders. The brine in the first cylinder passes through tubes heated by steam. The brine boils and its steam enters the next cylinder, where it heats the brine there. The steam from this brine heats the brine in the next cylinder, and so on. In each cylinder the condensation of steam causes the pressure inside to drop, allowing the brine to boil at a lower temperature. Salt is removed from the bottom of the cylinders as a thick slurry. It is filtered to remove excess brine, dried, and passed through screens to sort the particles by size. Salt made this way is known as vacuum pan salt and consists of small cubic crystals.
7 Brine may also be processed in a grainer. The brine is chemically purified and pumped into a long open pan heated by steam running through pipes immersed in the brine. The brine is heated to a temperature slightly below the boiling point and flakes of salt form on its surface as it evaporates. Usually a temperature of about 194°F (90°C) is used. Lower temperatures produce larger flakes and higher temperatures produce smaller flakes. The flakes grow until they sink to the bottom of the pan, where they are collected and dried. Grainer salt consists of small flakes rather than cubes and is preferred for certain uses in food processing. Sometimes the Alberger process is used, in which the brine is first partially evaporated in a vacuum evaporator then moved to a grainer. This process produces a mixture of flakes and cubes.
8 At this point salt used for most purposes is ready to be packaged in bags or boxes and shipped to consumers. To make iodized table salt, however, potassium iodide is added, then magnesium carbonate, calcium silicate, calcium phosphate, magnesium silicate, or calcium carbonate is added to make it free-flowing. The salt is then packaged and shipped to restaurants and grocery stores.
Quality Control
Specifications for salt vary widely according to the intended use. Salt intended for human consumption must be much purer than salt used for melting snow and ice, but salt used for certain scientific purposes may need to be even purer.
For most purposes, rock salt is allowed to have a gray, pink, or brown tinge rather than being pure white. The impurities that cause these colors may make up as much as 4% of a test sample. To test solubility, a 0.7-ounce (20 g) sample is placed in 6.8 fluid ounces (200 ml) of water. It should completely dissolve in no more than 20 minutes.
Evaporated salt intended for food processing is very pure, containing as much as 99.99% sodium chloride before additives are mixed in. This is important not only for safety and good taste, but because certain impurities can cause problems with certain foods. For example, small amounts of calcium tend to toughen vegetables. Traces of copper or iron tend to destroy vitamin C and to increase the rate at which fatty foods become rancid. In addition, calcium and magnesium both tend to make salt absorb more water, causing it to cake.
Health Aspects
Salt intake—or more precisely, sodium intake—is a controversial topic in health care today. Healthy adults can safely consume 0.2-0.4 ounces (6-11 g) of salt daily, which is equivalent to 0.08-0.14 ounces (2400-4400 mg) of sodium. For some people with high blood pressure, salt intake should be reduced. About one-third to one-half of all hypertensive people are salt-sensitive and will benefit from a low-sodium diet. Since there is no way to tell who these people are, most hypertensives under medical care will be placed on such a diet to see if it helps. A low-sodium diet usually aims to reduce sodium intake to less than 0.08 ounces (2400 mg) per day. While some have suggested that everyone should reduce salt intake, others point out that there is no evidence that salt restriction is of any benefit to otherwise healthy individuals.
