Parts of a Telephone

A basic telephone set contains a transmitter that transfers the caller's voice; a receiver that amplifies sound from an incoming call; a rotary or push-button dial; a ringer or alerter; and a small assembly of electrical parts, called the antisidetone network, that keeps the caller's voice from sounding too loud through the receiver. If it is a two-piece telephone set, the transmitter and receiver are mounted in the handset, the ringer is typically in the base, and the dial may be in either the base or handset. The handset cord connects the base to the handset, and the line cord connects the telephone to the telephone line.

More sophisticated telephones may vary from this pattern. A speakerphone has a microphone and speaker in the base in addition to the transmitter and receiver in the handset. Speakerphones allow callers' hands to be free, and allow more than two people to listen and speak during a call. In a cordless phone, the handset cord is replaced by a radio link between the handset and base, but a line cord is still used. This allows a caller to move about in a limited area while on the telephone. A cellular phone has extremely miniaturized components that make it possible to combine the base and handset into one handheld unit. No line or handset cords are needed with a cellular phone. A cellular phone permits more mobility than a cordless phone.

A Transmitter

There are two common kinds of telephone transmitters: the carbon transmitter and the electret transmitter. The carbon transmitter is constructed by placing carbon granules between metal plates called electrodes. One of the metal plates is a thin diaphragm that takes variations in pressure caused by sound waves and transmits these variations to the carbon granules. The electrodes conduct electricity that flows through the carbon. Variations in pressure caused by sound waves hitting the diaphragm cause the electrical resistance of the carbon to vary—when the grains are squeezed together, they conduct electricity more easily; and when they are far apart, they conduct electricity less efficiently. The resultant current varies with the sound-wave pressure applied to the transmitter.

The electret transmitter is composed of a thin disk of metal-coated plastic and a thicker, hollow metal disk. In the handset, the plastic disk is held slightly above most of the metal disk. The plastic disk is electrically charged, and an electric field is created in the space where the disks do not touch. Sound waves from the caller's voice cause the plastic disk to vibrate, which changes the distance between the disks, and so changes the intensity of the electric field between them. The variations in the electric field are translated into variations of electric current, which travels across telephone lines. An amplifier using transistors is needed with an electret transmitter to obtain sufficiently strong variations of electric current.

B Receiver

The receiver of a telephone set is made from a flat ring of magnetic material with a short cuff of the same material attached to the ring's outer rim. Underneath the magnetic ring and inside the magnetic cuff is a coil of wire through which electric current, representing the sounds from the distant telephone, flows. A thin diaphragm of magnetic material is suspended from the inside edges of the magnetic ring so it is positioned between the magnet and the coil. The magnetic field created by the magnet changes with the current in the coil and makes the diaphragm vibrate. The vibrating diaphragm creates sound waves that replicate the sounds that were transformed into electricity by the other person's transmitter.

C Alerter

The alerter in a telephone is usually called the ringer, because for most of the telephone's history, a bell was used to indicate a call. The alerter responds only to a special frequency of electricity that is sent by the exchange in response to the request for that telephone number.

D Dial

The telephone dial has undergone major changes in its history. Two forms of dialing still exist within the telephone system: dial pulse from a rotary dial, and multifrequency tone, which is commonly called by its original trade name of Touch-Tone, from a push-button dial.

In a rotary dial, the numerals one to nine, followed by zero, are placed in a circle behind round holes in a movable plate. The user places a finger in the hole corresponding to the desired digit and rotates the movable plate clockwise until the user's finger hits the finger stop; then the user removes the finger. A spring mechanism causes the plate to return to its starting position, and, while the plate is turning, the mechanism opens an electrical switch the number of times equal to the dial digit. Zero receives ten switch openings since it is the last digit on the dial. The result is a number of "dial pulses" in the electrical current flowing between the telephone set and the exchange. Equipment at the exchange counts these pulses to determine the number being called.

The rotary dial has been used since the 1920s. But mechanical dials are expensive to repair and the rotary-dialing process itself is slow, especially if a long string of digits is dialed. The development of inexpensive and reliable amplification provided by the introduction of the transistor in the 1960s made practical the design of a dialing system based on the transmission of relatively low power tones instead of the higher-power dial pulses.

Today most telephones have push buttons instead of a rotary dial. Touch-Tone is an optional service, and telephone companies still maintain the ability to receive pulse dialing. Push-button telephones usually have a switch on the base that the customer can set to determine whether the telephone will send pulses or tones.

Date: 2016-01-14; view: 895