Home Random Page


CATEGORIES:

BiologyChemistryConstructionCultureEcologyEconomyElectronicsFinanceGeographyHistoryInformaticsLawMathematicsMechanicsMedicineOtherPedagogyPhilosophyPhysicsPolicyPsychologySociologySportTourism






Checking for rear suspension linkage play

Inspect the area above and around the front fork oil seals (see illustration 6).There should be no sign of oil on the fork tube (stanchion) nor leaking down the slider (lower


leg). On models so equipped, check that there is no oil leaking from the anti-dive units. • On models with swingarm front suspension, check that there is no freeplay in the linkage when moved from side to side.

Rear suspension

• With the motorcycle off the stand and an assistant supporting the motorcycle by its handlebars, bounce the rear suspension (see illustration 7).Check that the suspension components do not foul on any of the cycle parts and check that the shock absorber(s) provide adequate damping.

• Visually Inspect the shock absorber(s) and


check that there is no sign of oil leakage from its damper. This is somewhat restricted on certain single shock models due to the location of the shock absorber.

• With the rear wheel raised off the ground, grasp the wheel at the highest point and attempt to pull it up (see illustration 8).Any play in the swingarm pivot or suspension linkage bearings will be felt as movement. Note:Do not confuse play with actual suspension movement. Failure to lubricate suspension linkage bearings can lead to bearing failure (see illustration 9).

• With the rear wheel raised off the ground, grasp the swingarm ends and attempt to move the swingarm from side to side and forwards and backwards - any play indicates wear of the swingarm pivot bearings (see illustration 10).


 



 


 


Worn suspension linkage pivots (arrows) are usually the cause of play in the rear suspension


Grasp the swingarm at the ends to check for play in its pivot bearings


ref.30 MOT Test Checks



Brake pad wear can usually be viewed without removing the

caliper. Mostpads have wear indicator grooves (1) and some also

Have indicator tangs (2)

Brakes, Wheels and Tyres


On drum brakes, check the angle of the operating lever with the

Brake fully applied. Most drum brakes have a wear indicator

Pointer and scale.


 


• With the wheel raised off the ground, apply the brake then free it off, and check that the wheel is about to revolve freely without brake drag.

• On disc brakes, examine the disc itself. Check that it is securely mounted and not cracked.

• On disc brakes, view the pad material through the caliper mouth and check that the pads are not worn down beyond the limit (see illustration 11).

• On drum brakes, check that when the brake is applied the angle between the operating lever and cable or rod is not too great (see illustration 12).Check also that the operating lever doesn't foul any other components.

• On disc brakes, examine the flexible


hoses from top to bottom. Have an assistant hold the brake on so that the fluid in the hose is under pressure, and check that there is no sign of fluid leakage, bulges or cracking. If there are any metal brake pipes or unions, check that these are free from corrosion and damage. Where a brake-linked anti-dive system is fitted, check the hoses to the anti-dive in a similar manner.



• Check that the rear brake torque arm is secure and that its fasteners are secured by self-locking nuts or castellated nuts with split-pins or R-pins (see illustration 13).

• On models with ABS, check that the self-check warning light in the instrument panel works.

• The MOT tester will perform a test of the motorcycle's braking efficiency based on a calculation of rider and motorcycle weight. Although this cannot be carried out at home, you can at least ensure that the braking systems are properly maintained. For hydraulic disc brakes, check the fluid level,


lever/pedal feel (bleed of air if its spongy) and pad material. For drum brakes, check adjustment, cable or rod operation and shoe lining thickness.

Wheels and tyres

• Check the wheel condition. Cast wheels should be free from cracks and if of the built-up design, all fasteners should be secure. Spoked wheels should be checked for broken, corroded, loose or bent spokes.

• With the wheel raised off the ground, spin the wheel and visually check that the tyre and wheel run true. Check that the tyre does not foul the suspension or mudguards.

• With the wheel raised off the ground, grasp the wheel and attempt to move it about the axle (spindle) (see illustration 14).Any play felt here indicates wheel bearing failure.



Date: 2016-01-14; view: 811


<== previous page | next page ==>
Steering and Suspension | Use a suitable battery charger - this kit also assess battery condition
doclecture.net - lectures - 2014-2024 year. Copyright infringement or personal data (0.009 sec.)