Home Random Page


CATEGORIES:

BiologyChemistryConstructionCultureEcologyEconomyElectronicsFinanceGeographyHistoryInformaticsLawMathematicsMechanicsMedicineOtherPedagogyPhilosophyPhysicsPolicyPsychologySociologySportTourism






Note how bracket (A) fits in slot (B)


12.8a Remove caps and remove the nut from the right side...


12.8b ... then withdraw the pivot bolt from theleft


 


washers and the chainguard. Note the position of the washers and how the slot in the front edge of the chainguard locates over a bracket on the swingarm (see illustration).


12.9 Lower swingarm to clear coolant reservoir (arrowed)

6Place a suitable container underneath thecoolant reservoir and detach the radiator overflow hose (see Chapter 3, Sec­tion 3).

7 Unscrew theshock absorber lower mounting bolts and pull the shocks free of the swingarm mounting brackets (see illustration 10.3a).

8Remove the caps from the swingarm pivot points (see illustration).Unscrew the nut on the right-hand end of the swingarm pivot bolt and withdraw the bolt while supporting the swingarm (seeillustration).

9 Lower the swingarm out of the frame in order to clear the coolant reservoir (see illustration).Ensure the left and right-hand


pivot bolt sleeves are retained inside the swingarm dust seals (see Section 13).

10If necessary, unscrew the screw securing
the drive chain slider to the swingarm, remove
the shouldered washer and unclip the slider
from the swingarm (see illustrations).

Installation


12.10a Drive chain slider retaining screw (A) and shouldered washer (B)

11If removed, install the drive chain slider (see illustrations 13.10a, b and c)and lubricate the bearings, dust seals, sleeves and the pivot bolt with grease.

12Offer up the swingarm, ensuring it is correctly positioned between the top and bottom runs of the drive chain and that none of the breather hoses are pinched behind the engine unit. Align the swingarm with the pivot bolt lugs and install the pivot bolt through the frame and swingarm from the left-hand side (see illustration).Install the pivot bolt nut and tighten to the torque setting specified atthe


beginning of this Chapter. Check that the swingarm pivots freely without binding and refit the pivot caps.

13Engage the lower ends of the shock absorbers in the swingarm mounting brackets, install themounting bolts and tighten to the specified torque setting.

14 Connect the radiator overflow hose to the coolant reservoir and refill the reservoir (see Chapter 3).

15Position the chainguard over the chain and align the guard with its mounting brackets, noting the alignment tab and slot on the front mounting. Install the shouldered washes and tighten the nuts securely.

16 Install the chain tensioners.

17 On R and T models, if removed, install the brake torque arm between the two halves of the bracket on the swingarm. Fit the mounting bolt from the right-hand side and then the spring washer, plain washer and nut from the left-hand side of the bracket. Tighten the nut securely and fit a new split pin. Connect the brake pedal return spring to the lug on the swingarm and install the rear wheel.

18On V, W. SW, X, SX, Y and SY models, engage the lug on the brake caliper bracket with the socket on the swingarm and install the rear wheel. Install the bolt securing the rear brake hose clamp to the swingarm and tighten the bolt securely.



19Install the silencer (see Chapter 4).

20Check and adjust the drive chain slack (see Chapter 1). Check the operation of the rear suspension before taking the machine on the road.


 



^M


Date: 2016-01-14; view: 640


<== previous page | next page ==>
B ... then pull the shock off the upper bracket | B Clips (A) on chain slider engage in holes (B) in swingarm
doclecture.net - lectures - 2014-2024 year. Copyright infringement or personal data (0.009 sec.)